ios-personmd-notifications md-help-circle

Profile

  • Guest
    medal 0
  • Posts: 21
  • Post Likes: 3765

Notifications

  • No Unread Notifications

Setups not saving

warning
This thread is closed. Threads older than 6 weeks are closed automatically. To continue this discussion, create a new thread.
angle-double-left ios-arrow-back 1 ios-arrow-forward angle-double-right
md-lock This topic has been closed by the moderator
medal 5000
12 years 184 days ago
Still having problems with setups not saving. I'm so paranoid about it now (because it's happened a few times to me and my friends) that I always log out and log back in multiple times to triple check that it has saved.

Just did my setup for tomorrows race. Five stops softs @ Spain, with my setup all dialed in, clicked save (and the button went from green to grey as it should) and logged out.

Logged back in two minutes later, only to find that it had reset itself to default once again.



Now it's not really a problem because my practice runs tell me what my setup was, so I can dial it back in easy enough, but it's still a pain having to do this.
md-quotelink
medal 5000
12 years 184 days ago
wot i tend to do if this happens is go to assembly and click a part to refit then remove it that brings up the save all. it a quick fix for ya till a dev can give you a better answer
md-quotelink
medal 5000
12 years 184 days ago
I know the problem you're talking about (i've had that before) but this isn't the problem I'm having.

The setup button was still green. I clicked it, and it saved fine (apparently)

Upon logging out and then logging back in, my setups had reverted back to default, but my parts refittings are still ticked correctly. It's like it's only half saving.
md-quotelink
medal 5000
12 years 184 days ago
no but if you do what Norrie said the date should go in twice.
md-quotelink
medal 5000
12 years 184 days ago
I don't understand what you guys are saying.

If you're thinking i'm only saving my setup once, then that is not the case.

I dial one driver in. Click save. Dial the other driver in. Click save. Dial in my refitting parts. Click save. I then head over to the design section, and move around my designers to release new parts daily. Click save. I'm constantly saving data as I go. I don't just do it all and then save it once only at the end.

This is a bug, I saved everything multiple times before I logged out. I'm not the first person to have this problem. The other day a friend of mine (in our two car league) had a similar problem, except his only reverted back for one of his drivers. One was on the correct strategy and the other reverted to default.
md-quotelink
medal 5000
12 years 184 days ago
Do you use Chrome?
md-quotelink
medal 5000
12 years 184 days ago
Nope, this was all done on Firefox.
md-quotelink
medal 5025 CEO & CTO
12 years 184 days ago
I'm investigating issues in this area now, to stop the button from greying out on test runs. It's somewhat of a mystery at the moment why this has started happening out of nowhere. I'm stepping through the code to see if anything jumps out.

I suspect your issues will be resolved by this evening if I can fix this today.
md-quotelink
medal 5000
12 years 184 days ago
"Jack
I'm investigating issues in this area now, to stop the button from greying out on test runs. It's somewhat of a mystery at the moment why this has started happening out of nowhere. I'm stepping through the code to see if anything jumps out.

I suspect your issues will be resolved by this evening if I fix this.

dont no if this helps jack but when i run my test runs it says car on track in the lap time section. if i change ma setup b4 the car is back in then the save all is still grey if i leave it to run till it says N/A then its not grey dont no if that will help.
md-quotelink
medal 5000
12 years 184 days ago
Thanks for the update Jack.
md-quotelink
medal 5000
12 years 184 days ago
The same sort of thing happens with me. Usually the problem is sorted by refreshing the page, or dialing it back in after reviewing the test runs.
md-quotelink
medal 5000
12 years 184 days ago
Not saving to me too, but I do one tweak up and then down to a part and voila ! I can save.
md-quotelink
medal 5025 CEO & CTO
12 years 183 days ago
I know how to stop this from happening, but don't yet know why it is happening. So I've applied a temporary fix to stop it for now, but not knowing why it is happening is very frustrating!
md-quotelink
medal 5000
12 years 182 days ago
Just thought I'd add to this that after doing my test runs today on one of my drivers, it wouldn't let me save. The 'save all' button was green, but I couldn't press it, so I refreshed the page, it logged me out, and when I logged back in, my test runs on that driver hadn't been completed, and I only had 2 test runs left, meaning I couldn't maximise my setup.

In hinds sight, I probably should have written down the setup just in case, but alas, I didn't and has screwed me over :P 
md-quotelink
medal 5000
12 years 182 days ago
"Artomy
I don't understand what you guys are saying.

If you're thinking i'm only saving my setup once, then that is not the case.

I dial one driver in. Click save. Dial the other driver in. Click save. Dial in my refitting parts. Click save. I then head over to the design section, and move around my designers to release new parts daily. Click save. I'm constantly saving data as I go. I don't just do it all and then save it once only at the end.

This is a bug, I saved everything multiple times before I logged out. I'm not the first person to have this problem. The other day a friend of mine (in our two car league) had a similar problem, except his only reverted back for one of his drivers. One was on the correct strategy and the other reverted to default.

Ahh right, ok i get ya now
md-quotelink
medal 5000
12 years 182 days ago
This is not fixed. Sorry Jack.
md-quotelink
medal 5000
12 years 178 days ago
This is now fixed. Thank you
md-quotelink
md-lock This topic has been closed by the moderator
angle-double-left ios-arrow-back 1 ios-arrow-forward angle-double-right

You must be logged in to post a reply.